• Our Products • Violet Ray Machine Repair • Violet Ray Documentation
• Violet Ray - Violet Wand Safety • Contact  • About Steffan

• Home

We are a 'PayPal Verified' Merchant!

Bob Beck Protocol Information: If you would like to learn more about Bob Beck and the Beck Protocol, you can view one of Beck's lectures, by clicking on the following Link - Bob Beck "Take Back Your Power" Lecture Video. Beyond these videos, there is a wealth of information on the internet about the Bob Beck Protocol. In a nutshell however, the Bob Beck Protocol claims to lay out path to help one maintain optimum health through the use of relatively simple electronic devices. These include the blood electrification unit, a colloidal silver generator, a magnetic pulse device and a device to make ozonated water. To accompany the video, one can download the entire "Original" Bob Beck handout, "Take Back Your Power" (1MB PDF). This handout was provided to guests that attended Beck's "Take Back Your Power" lectures.

The electrical devices we sell are meant for experimental research only & not meant to diagnose, treat or cure any disease or condition. Please see a medical professional if your are ill or in poor health.

We are a 'PayPal Verified' Merchant.

MIGHTY MAG
•
Bob Beck Protocol
Deluxe Magnetic Pulser
(Mag Pulser)
•
Auto-Pulsing
Auto Off Digital Timer

New Features:

• Continuous Operation Design. The Mighty Mag can now be run non-stop without over heating!
• Cooling fan to insure temperature stability inside the Mighty Mag.
• Improved pulse frequency control with fine and coarse adjustment. A trim pot for the analog timing system, has been moved to the instrument panel, effectively adding a second dial and making it easier to precisely adjust the desired pulse frequency.
• An analog 0-500V panel meter has been added, allowing one to properly adjust the capacitor charge voltage to 340V. The capacitor fully charges in 4 seconds.

Other Features:

Deluxe Auto-Pulsing Bob Beck Mag Pulser features an inductor coil who's cable can be unplugged from the device.

The 3 digit LED, digital auto off timer function is a safety precaution to prevent accidental overheating of the inductor coil.

I have no way to personally measure the gauss, but the pulse coil will shoot a 1.5 inch fender washer across the room, or nearly from the floor to the ceiling. I can say however, that my mag pulser uses the same SCR, the same size capacitor and the same 2.5mH inductor coil as Sota Instruments' 6000 gauss mag pulser. So, logically it stands to reason that my pulse coil will emit a 6000 gauss pulse.

Specifications:

• Input Voltage: 120V (240V upon request)
• Power Consumption: 50 Watt
• Current: .5 Amp
• Inductor Coil: 18AWG 2.5mH
• Capacitor: Industry Standard 450V 600uF PhotoFlash Capacitor
• Capacitor Charge Time: 4 seconds to 340V.
• Capacitor Life: Minimum 100,000 discharges.
• Weight: 6.5 Lbs
• 10 Minute Auto Off *
• Pulse Frequency Range: From 1 pulse every 6 seconds to 2 pulses per second.
• Max Run Time: None
• Pulse Coil Use Time: 20 min @ 1 pulse/4sec. (Additional pulse coils can be purchased for $169)

* To prevent the possibility of the pulse coil from overheating accidentally, the Mighty Mag will shut off the charge circuit after 10 minutes of run-time. To start a new time cycle, simply push and release the red momentary switch. The fan will continue to run until the red power switch is turned off. Running the device at a faster pulse rate than 1 pulse every 4 sec., will lessen the effectiveness of the magnetic pulse and cause the pulse coil heat up more quickly. The pulse (inductor) coil can be placed into a freezer for faster cooling. Exceeding operational guidelines can damage or destroy the device and void warranty!

About The Pulse Coil: The induction coil was wet wound with 18 AWG double insulated magnet wire. That means that the wire on the coil will not move and hence the magnetic pulse will be totally silent. In order to make sure one is getting a pulse, bring something magnetic about two inches away from the pulse coil. The tug from the electromagnetic pulse can be felt. The magnetic field increases exponentially, the closer one gets to the coil. Allowing a magnetic object to accidentally slap against the pulse coil can damage the insulation on the coil, necessitating repair or replacement. The magnet wire insulation is pretty thick stuff and can tolerate temperatures up to 300ºF. If the pulse coil gets too hot to put your finger on it and keep it there, then the coil needs to cool down.

If operation from a 12V power supply is desired, one can accomplish this by using a minimum 150W, 12V -> 120V power inverter.

Warranty: This Bob Beck Style Mag Pulser is guaranteed to be free of defects and to operate properly for a period of one year from the date of purchase. Opening the case without my permission, will void the warranty. Please refer all servicing back to Steffan.

As always, I strive to make the best and safest machines possible. Consequently from time to time unannounced improvements in the machine's design may occur.